Name: Dodge 2500/3500 Front
SKU: 13-Current DRW, 14-Current All Dodge 2500/3500 F
Price: 110.00 USD
Availability: InStock

Start Over

Installation Instructions

Description

These Dodge mud flaps are a Drill-Less mud flap. They are approximately 3/8 inch thick and come in two widths and two lengths.

Application: FRONT of all full-size Dodge 2014 thru current single rear wheel 2500/3500 full-size pickups and 2013 thru current Dodge 3500 dually pickups.

Mounting: DuraFlap mounting hardware is made of stainless steel where available. Other mounting products are made of anti-corrosive and rust resistant materials. Our drill-less Mudflaps are custom designed to utilize existing factory holes and other mounting points available on your truck. Installation instructions are included.

Hardware: All required hardware and brackets are supplied with this mud flap.

Serviceability: Mud flap is pre-drilled and requires no drilling of holes in your truck. Allows for easy & precise alignment. This mud flap is cut to go around the hump in your wheel well, allowing for easy positioning.

Product Order Form: Truck & SUV

Hidden

Setup The Form

Hidden

Set Product Category

Hidden

Set Front Rear Mud Flap

Hidden

Set Vehicle Year

Hidden

Set Width Taxonomy

Hidden

Set Length Taxonomy

Hidden

Set 2wd/4wd Taxonomy

Hidden

Set Customizations Taxonomy

Hidden

Set Weight Design Taxonomy

Hidden

SKU Element 1 Front

Hidden

SKU Element 3 Front/Rear (F/R)

Hidden

SKU Element 4 Middle

Hidden

WooSKU

Tell us about your vehicle

Confirm the Year of Your Truck(Required)

Additional Customizations on Your Truck

Are your wheels/tires aftermarket?(Required)

Aftermarket wheels/tires often move then wheel outboard slightly. In order to keep your mud flap centered, we will need to create a custom shift and thus require some measurements.

Yes

No

Is your truck lifted?(Required)

Yes

No

Additional Customizations on Your Dually

Are dually's wheels/tires aftermarket?(Required)

Aftermarket wheels/tires often move then wheel outboard slightly. In order to keep your mud flap centered, we will need to create a custom shift and thus require some measurements.

Yes

No

Is your dually lifted?(Required)

Yes

No

Standard Configuration

The Long version of this mud flap may hang less than 6” off the ground. Verify the length of your mud flaps based on your truck height.

Have you measured from the fender to the ground and confirmed your length choice?

Yes

No

How long do you want your lifted truck's mud flaps?(Required)

Custom Measurements

Will you have a rub issue?(Required)

To check for a potential rub issue, place a thick piece of cardboard in the wheel well where the mud flap will be installed, and have a helper turn the wheels. Our material is about 5/16” thick.

Yes

No

When your truck has the potential for a rub issue, we recommend our LFT set-back brackets. Click Here for Lifted Truck Flaps

We will custom shift our drill-less mud flaps to your offset wheels, so they will be centered to your tires. We also make them custom length for your lift.

VERY IMPORTANT: Custom mud flaps are non-returnable, so please measure carefully. We are available to walk you through the measuring to ensure you get the measurements correct.

Which hole are you measuring from?(Required)

On your vehicle, there may be several holes available. Please tell us which one you will be measuring from.

The Available Measurement Holes the Dodge 2500/3500 Front

Click Here for a Printable Worksheet

1. Factory Hole to Ground(Required)

Please enter the exact number of inches from factory hole to the ground.

2. Mud Flap Clearance from the Ground(Required)

We recommend 7-9" (most curb heights are 6"), 7" if towing a boat or trailer 9" no towing.

3. How wide do you want your mud flap?(Required)

Width choice may increase the price for weights. We will contact you after placing your order if this is the case.

4. Factory Hole to Outside Tire(Required)

Please enter the exact number of inches from factory hole to the outside of the tire.

5. Overall width of your tire(s)(Required)

How do you want your truck mud flaps to look?

Please allow 3-4 weeks for shipment on custom orders.

Laser Cut Design Catalog

Custom Design Details

Complex or detailed designs exceeding 1 hour of design time may incur additional charges.

Attach the image of the design you'd like

Drop files here or

Accepted file types: jpg, gif, png, jpeg, pdf, eps, ai, tif, Max. file size: 128 MB, Max. files: 3.

Custom artwork request notes

Before you go

Do you have any additional comments or questions?

Our goal is to get you the perfect custom mud flap for your vehicle. If you need help, please let us know.

Mud Flap

Hidden

SKU

Hidden

SKU Element 3 L

Hidden

SKU Element 4 2WD

Custom SKU

Phone

This field is for validation purposes and should be left unchanged.

Subtotal
Options
Total

Most orders without custom weights ship in 1-3 days

Dodge 2500/3500 Front